Cleveland-motion-controls ULTRA ISC SERIES SLIM CELL TRANSDUCER REV AA Manual de usuario

INSTRUCTION MANUAL (MAN-70434-0) FOR ULTRA ISC SERIES SLIM CELL TRANSDUCER Cleveland Motion C

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 1.2 FEATURES Ultra ISC tension transducer features are:  Factory Calibration promote

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 1.5 GENERAL SPECIFICATIONS Item Specification Comments Input Supply Power Supply Requir

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 1.8 OPERATING CONDITIONS Condition Isolated Signal Conditioning Amplifier Installation

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER Output Impedance Approximately 64 Ohms per Bridge leg Maximum Voltage, Gage to Beam or Bas

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 1.13 BLOCK DIAGRAM OF ULTRA SERIES ISC AMPLIFIER MODULE Figure 2 Block Diagram of Ultra

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 2 PRODUCT COMPONENTS The Ultra Series ISC Slim Cell Tension Transducer (see Figure 3) consi

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 2.1 M12 MATING CONNECTOR The M12 connector used on the Ultra Series ISC amplifier is a f

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 2.2 ELECTRICAL CONNECTIONS AND WIRING Refer to Figure 5 for making the transducer to power

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 2.3 CABLING Important: Most start-up problems are the result of mis-wiring or failure to

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 2.4 POWER SUPPLY REQUIREMENTS For best performance, a regulated DC power supply that provi

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA REVISION HISTORY Rev ECO Author Date Description of Change AA XXX WGW As Release

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 2.5 POTENTIOMETERS ADJUSTMENTS (IF NEEDED) The gain and zero adjustments are factory pre

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 3 PRODUCT APPLICATION The Ultra Series Slim Cell Transducer utilizes a twin sensing beam.

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 3.2 SUMMING In the majority of applications, loadcells are used in pairs. The net tensi

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 3.3 SUMMING BY “SERIES STACKING” The final interface approach to be discussed is to “stack

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4 INSTALLATION 4.1 RECEIVING AND UNPACKING After receiving the Ultra ISC Slim Cell Transd

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.2.2 MOUNTING HARDWARE AND RECOMMENDED FASTENER TORQUE UltraSlim 1: Torque: ¼ - 20 x 1-

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.2.3 MOUNTING DIMENSIONS 62 ° OF ANGULAR ALIGNMENTWITH BOLT IN POSITIONSLIM CELLMOUNTIN

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER NC (3) NC (3) Z 2.50 3.30 NC (6) NC (6) Z 63.5 83.8 Table D Transducer and Mounting

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA PAGE 28 OF 42 4.2.4 SELECTING A MOUNTING LOCATION Select the mounting location for the

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.3 PRE-INSTALLATION PRECAUTIONS 4.3.1 SHIPPING Shock and vibration transmitted to the tran

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER WARRANTY AND LIMITATION OF LIABILITY All equipment is sold subject to the mutual agreement

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.4 INSTALLATION PRECAUTIONS To ensure proper installation and operation of the system,

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.6 POSITIONING THE SLIM CELL TRANSDUCER Use the following steps when positioning the tran

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.7 MOUNTING THE SENSING ROLL Be sure to exercise care during this portion of the instal

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.9 POWER-UP AND TESTING 4.9.1 BEFORE APPLYING POWER Before applying power, check the wiri

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.10 ADJUSTMENT TOOLS (ONLY IF NOT USING NUMERICAL CORRECTION) Using the correct tools s

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.12 PROPER PRACTICES FOR APPLYING CALIBRATION FORCES Seldom is a transducer oriented such

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA Examples of Force Loss due to Friction at Driven Roll In this example, only a fraction of

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER  Always apply and remove the test load in a continuously increasing or decreasing manner,

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.15 EMC CONNECTIONS AND INSTALLATION Compliance with the specified EMC directive for im

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 4.16 CABLE GLANDS Several manufacturers provide cable glands that can be used to ensure th

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA PAGE 4 OF 42 BLANK

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 5 TROUBLESHOOTING Do no let safety be an afterthought! Before installing, servicing or

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 5.1 TRANSDUCER BENCH TESTING Because the strain gage signal conditioning is completely int

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 6 MANUFACTURERS DECLARATION OF CONFORMITY Figure 13 EC Declaration of Conformity PAGE

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER TABLE OF CONTENTS 1 PRODUCT OVERVIEW ...

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA 4.10 ADJUSTMENT TOOLS (ONLY IF NOT USING NUMERICAL CORRECTION)...

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER WARRANTY Cleveland Motion Controls warrants the goods against defects in design, material

ULTRA ISC SERIES SLIM CELL TRANSDUCER MAN-70434-0 REV AA PAGE 8 OF 42 BLANK

MAN-70434-0 REV AA ULTRA ISC SERIES SLIM CELL TRANSDUCER 1 PRODUCT OVERVIEW 1.1 GENERAL DESCRIPTION The Ultra Series Integrated Signal Conditioning